Suction Brush Unit
Replacement Brush Series
Groove Brush
Standard Cleaning Model
This brush is a replacement brush designed exclusively for the Suction Brush Unit.
Angled bristles designed to fit into grooves
Groove Brush
Features
• Angled bristles designed to fit into grooves
• 25 mm bristle length
• Designed for cleaning narrow grooves and corners
• Compatible with the common head joiner used across the Sucking Brush series
Photos 1, 2, and 3 show the Heat-Resistant Brush 25.
The Groove Brush uses the same bristle structure.
Photo 1
Angled inward bristles designed to reach into grooves easily.
Conventional bristles are vertical or slightly flared outward.
Hard Type
Angled inward bristles designed to fit into grooves.
A versatile design for use in a variety of areas.
Photo 2
Photo 3
Photo shows the Heat-Resistant Brush 25
Bristle tips designed to contact the surface
The brush is designed so that the bristle tips make direct contact with the surface.
Because the bristles extend forward beyond the brush body, the body is less likely to hit the surface, making it easier to work in narrow spaces.
(Common design for all Brush Heads)
Brush Head Structure
Recommended Uses
-
Window tracks
-
Sliding door tracks
-
Window frames
-
Patio and balcony drainage grooves
-
Narrow gaps and hard-to-reach areas
-
RV and camper tracks, grooves, and tight spaces
Example of Use
Combined with the Soft Brush
Attach the Soft Brush on one side
and the Groove Brush on the other.
Apply cleaning solution and scrub away dirt
with a single tool.
This reduces the need to switch brushes
and improves work efficiency.
Combine the brushes freely
to suit the task.
Combination Example
Specifications
-
Head Material: PP
-
Bristle Material: PVC
-
Bristle Length: 25 mm Bristle Diameter: 0.5 mm
-
Recommended Use Temperature: 60°C (140°F) or below
-
Compatible Parts: Handle / Head Joiner
Features
About PVC (Polyvinyl Chloride)
• Provides moderate firmness and good cleaning performance
• Relatively resistant to acidic and alkaline cleaning agents
• Well suited for cleaning around water fixtures
• A proven material widely used for brushes
Operating Temperature
• Recommended operating temperature: 60°C (140°F) or below
Dimensions
Overall Dimensions: Approx. 70 × 65 mm
How to Connect (Common to All Brush Heads)
Connection
Align the Brush Head and Head Joiner in the correct direction.
Insert the Brush Head until it passes beyond the locking tab.
Locking Mechanism
The Brush Head and Head Joiner are securely held in place by the locking mechanism.
Insert the Head Joiner into the Handle.
The hexagonal shape ensures a secure connection.
Insert the Head Joiner fully and securely.
Make sure there is no gap between the Head Joiner and the Handle.
If the connection is incomplete, the part may come off during use.
Connection Complete
Removal
Press the locking tab while removing the Brush Head.
No tools are required.
Angle Adjustment
The Brush Head can rotate.
Adjust the angle to suit the area being cleaned.
There is no need to press the locking tab.
Useful Signboard Card for Cleaning Sites
After use, the backing card can be reused as a simple signboard.
It can be used to provide information or notices while working on site.
Go to Purchase Page
Product Specifications
-
1 Replacement Brush Head
-
Replacement part exclusively for the Suction Brush Unit
-
Not a suction-type brush
-
Made in Japan
For customers who do not have the Basic Unit,
set products for first-time buyers are also available. ▶ View Set Products
Please Check Before Purchase
-
This product is a replacement Brush Head.
-
Handle, Head Joiner, and hose are not included.
-
This product does not have a suction function (it is not a suction-type brush).
-
Brush color may vary slightly depending on the production lot.
-
Package design may change without notice.
-
Product performance and specifications are subject to change.
International Shipping
International shipping is currently being prepared.