Suction Brush Unit
Replacement Brush Series
Groove Brush
Step-Cut
Extended-Corner Model
This brush is a replacement brush designed exclusively for the Suction Brush Unit.
共通
The angled bristles and extended step-cut tip
help agitate and remove dirt from corners.
共通
Features
• The step-cut design fits
into grooves and corners
• Different bristle lengths help
remove dirt efficiently
• Angled bristles are designed
to reach into grooves
• Suitable for cleaning narrow
and detailed areas
• Compatible with the common
Head Joiner used across
the Sucking Brush series
The photo shows the Heat-Resistant Brush Step-Cut.
The step-cut shape is the same.
Photo shows the Heat-Resistant Brush 25
Bristle tips designed to contact the surface
The brush is designed so that the bristle tips make direct contact with the surface.
Because the bristles extend forward beyond the brush body, the body is less likely to hit the surface, making it easier to work in narrow spaces.
(Common design for all Brush Heads)
Brush Head Structure
Recommended Uses
• Window tracks
• Sliding door tracks
• Shower door tracks
• Patio and balcony drainage grooves
• Corners and narrow gaps
• Detail cleaning in hard-to-reach areas
• RV and camper window and door tracks
Example of Use
Combined with the Soft Brush
Attach the Soft Brush on one side
and the Heat-Resistant Step-Cut Brush
on the other.
Apply cleaning solution and clean
detailed areas
with a single tool.
This reduces the need to switch brushes
and improves work efficiency.
Combine the brushes freely
to suit the task.
Combination Example
Specifications
Head Material: PP
• Bristle Material: PVC
• Bristle Length: 25 mm + 30 mm at the tip
Bristle Diameter: 0.4 mm
• Recommended Use Temperature: 60°C (140°F) or below
• Compatible Parts: Handle
Head Joiner
Features
About PVC (Polyvinyl Chloride)
• Provides moderate firmness and good cleaning performance
• Relatively resistant to acidic and alkaline cleaning agents
• Well suited for cleaning around water fixtures
• A proven material widely used for brushes
Operating Temperature
• Recommended operating temperature: 60°C (140°F) or below
Dimensions
65mm
70mm
Overall Dimensions: Approx. 70 × 65 mm
How to Connect (Common to All Brush Heads)
Connection
Align the Brush Head and Head Joiner in the correct direction.
Insert the Brush Head until it passes beyond the locking tab.
Locking Mechanism
The Brush Head and Head Joiner are securely held in place by the locking mechanism.
Insert the Head Joiner into the Handle.
The hexagonal shape ensures a secure connection.
Insert the Head Joiner fully and securely.
Make sure there is no gap between the Head Joiner and the Handle.
If the connection is incomplete, the part may come off during use.
Connection Complete
Removal
Press the locking tab while removing the Brush Head.
No tools are required.
Angle Adjustment
The Brush Head can rotate.
Adjust the angle to suit the area being cleaned.
There is no need to press the locking tab.
Useful Signboard Card for Cleaning Sites
After use, the backing card can be reused as a simple signboard.
It can be used to provide information or notices while working on site.
Go to Purchase Page
Product Specifications
-
1 Replacement Brush Head
-
Replacement part exclusively for the Suction Brush Unit
-
Not a suction-type brush
-
Made in Japan
For customers who do not have the Basic Unit,
set products for first-time buyers are also available. ▶ View Set Products
Please Check Before Purchase
-
This product is a replacement Brush Head.
-
Handle, Head Joiner, and hose are not included.
-
This product does not have a suction function (it is not a suction-type brush).
-
Brush color may vary slightly depending on the production lot.
-
Package design may change without notice.
-
Product performance and specifications are subject to change.
International Shipping
International shipping is currently being prepared.