Suction Brush Unit
Replacement Brush Series
Hard Type
V-Cut
Designed for Uneven Surfaces
This brush is a replacement brush designed exclusively for the Suction Brush Unit.
Features
-
The V-cut shape conforms well to uneven surfaces.
-
Efficiently removes dirt from grout lines and embossed surfaces.
-
Uses thick, stiff PVC bristles.
-
Ideal for scrubbing stubborn dirt in corners and recessed areas that are difficult for the bristle tips to reach.
-
Compatible with the Head Joiner used throughout the Suction Brush Series.
-
Recommended for users who prioritize mechanical cleaning action.
※ Do not use on aluminum, resin products, or other surfaces that are easily scratched.
Brush Head Structure
Photo shows the Heat-Resistant Brush 25
Bristle tips designed to contact the surface
The brush is designed so that the bristle tips make direct contact with the surface.
Because the bristles extend forward beyond the brush body, the body is less likely to hit the surface, making it easier to work in narrow spaces.
(Common design for all Brush Heads)
Recommended Uses
-
Bathroom tile and grout
-
Textured and non-slip floors
-
Embossed vinyl flooring
-
Commercial kitchen floors
-
Patio, balcony, and outdoor floor grooves
-
Garage and utility-area floors
-
Corners and hard-to-reach areas
-
RV and camper floor grooves and tight spaces
Usage Example
When combined with the Soft Brush
A Soft Type can be attached to one side,
and a Hard Type V-Cut to the other.
This allows you to apply cleaning solution and clean grout lines or uneven surfaces with a single tool.
It reduces the need to change brushes and improves work efficiency.
Combine the brushes freely to suit the task.
Combination Example
Specifications
-
Head Material: PP
-
Bristle Material: PVC
-
Bristle Length: 25 mm Bristle Diameter: 0.5 mm
-
Recommended Use Temperature: 60°C (140°F) or below
-
Compatible Parts: Handle / Head Joiner
Features
About PVC (Polyvinyl Chloride)
• Provides moderate firmness and good cleaning performance
• Relatively resistant to acidic and alkaline cleaning agents
• Well suited for cleaning around water fixtures
• A proven material widely used for brushes
Operating Temperature
• Recommended operating temperature: 60°C (140°F) or below
Dimensions
Overall dimensions: approx. 70 × 60mm
How to Connect (Common to All Brush Heads)
Connection
Align the Brush Head and Head Joiner in the correct direction.
Insert the Brush Head until it passes beyond the locking tab.
Locking Mechanism
The Brush Head and Head Joiner are securely held in place by the locking mechanism.
Insert the Head Joiner into the Handle.
The hexagonal shape ensures a secure connection.
Insert the Head Joiner fully and securely.
Make sure there is no gap between the Head Joiner and the Handle.
If the connection is incomplete, the part may come off during use.
Connection Complete
Removal
Press the locking tab while removing the Brush Head.
No tools are required.
Angle Adjustment
The Brush Head can rotate.
Adjust the angle to suit the area being cleaned.
There is no need to press the locking tab.
Useful Signboard Card for Cleaning Sites
After use, the backing card can be reused as a simple signboard.
It can be used to provide information or notices while working on site.
Go to Purchase Page
Product Specifications
-
1 Replacement Brush Head
-
Replacement part exclusively for the Suction Brush Unit
-
Not a suction-type brush
-
Made in Japan
For customers who do not have the Basic Unit,
set products for first-time buyers are also available. ▶ View Set Products
Please Check Before Purchase
-
This product is a replacement Brush Head.
-
Handle, Head Joiner, and hose are not included.
-
This product does not have a suction function (it is not a suction-type brush).
-
Brush color may vary slightly depending on the production lot.
-
Package design may change without notice.
-
Product performance and specifications are subject to change.
International Shipping
International shipping is currently being prepared.